A Samsung Washer displays a dC3 error code when a Add Door Error has been detected by the internal electronic diagnostics.

Calibration mode will rotate the tub or drum back and forth for 1-3 minutes and then end by itself. However, Calibration mode will not calibrate correctly unless the washing machine is empty. If there is something in the washing machine, remove it and then run Calibration mode again with the washer empty, so your washer is properly …

The UE or DC error code indicates unbalanced load. To resolve this issue; refer to the troubleshooting steps given below: Front Load Machines: 1 Turn off and …

When your Samsung washer displays the UR, E4, UE, or DC codes, that indicates the machine has a problem with an imbalanced load. That is most likely …

Re-plug and restart the washing machine by pressing START/PAUSE button. Note: If you have any questions after verifying the above-mentioned solutions, please call our contact center to get help with your inquiry.

You can correct minor problems in Samsung devices work yourself. The complex electronics repair requires the help of a specialist.

The auxiliary door is a helpful feature of Samsung washing machines that helps you add more clothes to the washer from a smaller door during the cycle wash. You will get a DDC message if you open the add door without hitting the pause button.

This free guide will give you an overview of the various Samsung washing machine codes, what they stand for and how to fix the issues, if possible. Skip to content 1-888-454-4840

Reply. Jam1eM. Samsung Pro. 20-10-2021 08:30 AM. dC check code means the main door is either detecting it is not closed properly or the door lock is unable to latch and lock. if the door is closed firmly and there are no dents to the front panel affecting the angle of the door it should lock ok. If not then yes it needs an engineer.

Costs about 50 euro instead of 150 for having a technician come to you and most possibly make the same diagnoses but then asks you to pay the add. costs to replace the lock. Find the piece that corresponds with your …

The DC error code on a Samsung washing machine signifies that the load is unbalanced. This typically happens when there's too much laundry loaded on one side of the drum, restricting the washer's ability to …

Sears can help you troubleshoot repairs when your Samsung washing machine has a DC error code. If you need help fixing the problem, book an appointment today.

What to do if you get the Samsung Washer DC code? Contents hide. Solution 1: Take Excessive Clothes Out Or Put More If There is a Single Item load. Solution 2: Check for Damaged Parts. Solution 3: Level the Washer. Solution 1: Take Excessive Clothes Out Or Put More If There is a Single Item load.

Your appliance will display a UE code when it has detected an unbalanced load and has stopped the spin for safety reasons. Make sure the appliance is on a flat, stable surface, then follow the steps outlined below. Calibrate your washing machine. Rebalance the load. Run a drain cycle.

How to Reset the Samsung Washing Machine's Eco Bubble (steps) Step 1: Begin by turning on the washing machine. To turn it on, you plainly need to touch the power button. Step 2: Select an option by pressing the option button. Then, for about 5 seconds, push the option button on the machine.

When your Samsung washer displays the UR, E4, UE, or DC codes, that indicates the machine has a problem with an imbalanced load. That is most likely caused by oversized items inside or because you're washing an undersized load.

These codes signal an issue with water not filling the machine appropriately. In the case of code 11E, there is a low water level detected. Two potential problems can cause this issue: a faulty water inlet valve or the water tap is off.

A Samsung Washer displays a dC1 error code when a Door Lock Error has been detected by the internal electronic diagnostics.

Reset the washing machine and select a new program. 13. 9H1, 9E1, and 9E2. Power fault. Test the power cord, fuse, and socket for continuity and replace the faulty one. 14. tE, tE1 – tE3, and tC1 – tC3. Temperature sensor issue. Unplug the …

Most often, the DC error code can be resolved by redistributing the weight of existing items in the washing machine. Common causes of unbalanced loadsare: 1. bulky items such as bedsheets, comforters, and towels 2. jeans, sweaters, and jackets 3. oversized loads 4. undersized loads If you get a DC code error, che…

The "DC" in "DC" on Samsung washer stands for "Direct Drive," indicating that the washer uses a direct drive motor system instead of a traditional belt and pulley system. 2. Samsung introduced the Direct Drive technology in its washers to reduce noise and vibration levels, resulting in a quieter and more stable washing experience. 3.

Open the door. Place a container under it and remove the plug of the pump. Drain the water and then open the door of the washer. Place the laundry evenly by hand or remove half of the items from the tub. Then resume the washing cycle. How to fix the DC Code on the Samsung Washing Machine. It is easier to rearrange the laundry in top-load ...

1C. The Water Level sensor is not working properly. • Switch off the appliance at the mains then wait 30 seconds. Switch the appliance back on again and start a new program. • If the information code remains, contact a customer service center. 3C. Motor problem. • Try restarting the cycle. • If the problem continues, call for service.

When the washing machine isn't sitting level on the floor, the washer will not be balanced, and the DC code will appear. Here's how to check if your washing machine is level: Use a leveling tool to check if …

Here are a few steps you can take to resolve the issue: Open the door: Pause the cycle and open the door of the washing machine. Ensure that no clothes are gathered in a single location or clumped together. Redistribute the load: Evenly spread the clothes inside the drum to balance the weight distribution.

How To Check the Samsung DC64-01538A And DC34-00026A Washer Door Lock Switch

If your washing machine doesn't balance on an uneven surface, there are a few options. One is to try to adjust the leveling pegs in the legs of the washing machine.

If you own Samsung home appliances such as a washer or dryer, you would be very familiar with the DC code, which is often displayed when there is something wrong with the machine. Also, the DC code doesn't signify similar problems between two different machines. Every machine has its own set of warnings when the DC code appears.

The DC error code indicates that the load in your washing machine isn't balanced, which means the washer can't spin correctly. In this guide, we give you step-by-step instructions for finding the underlying cause of the …

Other reasons for flashing Dc code on the Samsung washer are technical faults. These faults include a problem with the door hatch, main lock, mechanically damaged or worn out door, and damaged wiring between the …